Download a terminal emulator application to a PC
You can use any standard software terminal emulator to connect to the 3300 ICP. However, the instructions provided here are for the Tera Term (Pro) emulator, a free software terminal emulator for MS-Windows. You can download the Tera Term (Pro) emulator from the Internet at the following URL: http://hp.vector.co.jp/authors/VA002416/teraterm.html
Connect the PC to the controller as follows:
Connect a LAN crossover cable from the Ethernet port on the PC directly to the WAN port on the controller
Connect an RS-232 serial cable between COM port 1 on the PC and the RS-232 Maintenance port on the front panel of the controller.
Log into a Customer Data Entry (CDE) session on the 3300 ICP
Note: The PC connected to the WAN port must be on the same subnet as the System IP Address.
You program the MLPP by using both the System Administration Tool and the Customer Data Entry (CDE) facility. CDE is used to program the enhanced login security options required by MLPP. The remaining programming is done using the System Administration Tool.
Note: WAN-related forms (IP Routing, WAN Settings, Remote Access (PPTP), Firewall Control, Port Forward Table) do not apply when MLPP is enabled and should not be programmed.
To program MLPP:
Set the MLPP Application field to "Yes".
Program the MLPP Access Digit that subscribers must dial to initiate a call at a precedence level above Routine.
Enter a single digit in the range of 2 to 9. The digits 0 and 1, and characters such as #, are not supported.
Complete this form to control how the system treats various intercept conditions as they arise in call processing. Calls can be routed to the directory number of a Recorded Announcement Device, or to a reorder tone (the default). At minimum, announcements are required for the following conditions: for Blocked Precedence, Unauthorized Precedence, Cannot Preempt, Unassigned Directory Number, Trunk Out of Service, and Attendant Night Service 1 and Night Service 2. Only the first intercept handler (Intercept Number 1) is required for each night service mode. If using a directory number, enter the MLPP Call Diversion answer point DN from the MLPP Assignment form. Other DNs are not allowed.
Program the routing destination for calls when the Call Diversion Answer Point is Out of Service or in Do Not Disturb.
(Optional) Program the SC1000 or 5540 IP Console if using as the MLPP Call Diversion Answer Point. See Program DNI Consoles for instructions.
(Recommended)
Telephone
Directory Assignment form
Although not mandatory, names should be given to the RAD Directory
Numbers used for MLPP intercepts
Program the telephones:
Program Digital trunks for MLPP. Only T1 ISDN PRI trunks are supported.
Protocol Assignment form for embedded TI or IMAT PRI Link Characteristics for NSU
Configure for NI2 ISDN
Set "Enable NI2 Service Messages" to "Yes."
If users require access to trunks that are not part of the DNS, program service digits as leading digits in the ARS Leading Digits Assignment form that will allow access to the trunks. Service calls are sent as Routine precedence level. Users can only dial service digits on external calls.
Disable the Auto-Campon Timer.
Enable "Call Forwarding Reminder Ring (CFFM and CFIAH only)"
Set "Disable Conference Join Tone" and "Disable Executive Busy Override Tone" to "No."
Set "Call Forward Accept" to "Yes" for devices programmed in the MLPP Assignment form as the MLPP Call Diversion answer point.
Set the T1-619a Signalling (MLPP Only) field to "Yes" for ISDN PRI links that are connected to the DSN Defense Switched Network.
System Options Assignment form. Disable the following:
Set Registration Access Code
Set Replacement Access Code
Conference/Call Intrusion Repetitive Tone Timer
Enable Traveling Class Marks if the system is in a cluster.
MLPP Assignment form
Enter both the system-wide and the subscriber-specific MLPP data in the MLPP Assignment form.
Note: The MLPP Assignment form is not supported by the System Data Synchronization feature. If MLPP is deployed in a clustered or resilient environment, you will need to program the MLPP Assignment form with identical data on each cluster element or each resilient controller pair.
Complete this form as required.
LAN Policy (QoS) form
Program the DSCP and L2 priority.
IP Port Filter form
Complete this form as required to secure IP ports on the controller against unauthorized access.
For CXi controllers only,
Layer 2 Switch form – Disable LAN ports 2-16
Spanning Tree form – Set the Priority of port 1 to the highest value (15).
Note: Layer 2 Switch and Spanning Tree forms are not applicable to MCD for Mitel Communications Suite (MCS).
Log into a Customer Data Entry session to complete the following programming:
Enable "Enhanced Login Security"; see Security Options Assignment for more information.
Assign administrator rights to control access to the CDE/Maintenance facility; see User Authorization Profile for more information.
Customize the text that appears on-screen when the administrator logs onto the CDE/Maintenance facility; see Login Banner Assignment for more information.
